Satish Injecto-Plast,Ambad,Nasik   MAKE   Ferromatic Engel Ferromatic Haitain Ferromatic Ferromatic Engel Haitan Haitan Haitan MACHINE SPECIFICATION Sr. No. Description  Unit H8- 250T H9 - 175T H10-125T H11-86T H12-80T H14-50T H13-50T H15-160T H16-90T H17-60T 1 Screw Diameter mm 55 50 40 34 32 28 30 40 32 26 2 Inj.pressure kg/cm*cm 1919 208 1901 206 Mpa 2074 2068 2699Bar 240Mpa 237Mpa 236Mpa 3 Shot weigth gm 588 300 216 131 99 64   230 110 60 4 Screw L/D ratio - 23.6 20 12:00 21.2 14:24 23         5  Screw strock mm 260 190 180   542 110   201 150 125 6 Screw speed rpm 229 230 329 206 400 400   245 250 260 7 Nozzle contact force tons   6.7 _ _ _ _   _ _ _ 8 Inj.rate cc/sec 252 255 130   105 87 80 125 87 60 9 Plasticizing capacity gm/sec 40 55 25   15 12   15.4 11 7 10 Type of clamping - Ram Ram Toggle Toggle Toggle Toggle Ram Toggle Toggle Toggle 11 Clamping force tons 250 175 125 86 80 50 50 160 90 60 12 Max.daylight mm 950 550 825   710 630   950 700 600 13 Min. mould height mm 200 250 150 150 150 150   180 150 120 14 Max. mould height mm 750 400 475 360 400 350   520 380 330 15 Space between tie bar mm 620X620 ---- 435X435 360X360 405X360 325X310   470X470 360 x360 310X310 16 Hyd. Ejector force tons 7 7 3.6 5 3.4 3.2 3.98 3.3 3.3 2.2 17 Hyd. Ejector stroke mm 100 150 120 33 120 100 100 140 100 22 18 Pump driving motor kw 37 30 15 7.5 15 11 15 22 15 11 19 Heater capacity kw 23.7 18.5 13.1 5.7 7.3 6.4   11.25 6.2 5.1 20 Total connecting load kw 60.7 66 22.3 13.2 21.4 17.4   33.25 21.2 16.1 21 Temp. controller zone - 3 5 3 5 3 4 4 4 4 4 22 Oil tank capacity ltrs 720 610 220 200 220 208   350 240 180 23 m/c wt tons 13.5 11.5 4 3.45 3.152 2.465   5.3 3.46 2.5 24 m/c dia. mxmxm 6.54X1.73X2.5 6.3X1.8X2.2 4.5X1.5X2.2 4.5*1.25*1.9 3.8X1.4X2.1 3.5X1.2X2.1   5.15X1.35X1.96 4.32X1.23X1.86 3.76X1.13X1.76 25 Nozzle radius mm R12 R12 R15 R12 R15 R12   R12 R12 R12 26 Pattern hole dia mm 20 16   16 16 16   16 16 16 27 Locating ring Dia. mm 120 120 120 120 120 120 120 125 125 100